13 Xinren Road,Huangtang Economic Zone, Jiangyin, China
The plate heat exchanger consists of a pack of corrugated metal plates with portholes for the passage of the two fluids between which heat transfer will take place. The plate pack is assembled between a fix frame plate and a movable pressure plate and compressed by tightening bolts. The plates are fitted with a gasket which seals the inter plate channel and directs the fluids into alternate channels. The number of plates is determined by the flow rate, physical properties of the fluids, pressure drop and temperature program. The plate corrugations promote fluid turbulence and support the plates against differential pressure. The frame plate and the pressure plate are suspended from an upper carrying bar and located by a lower guiding bar, both of which are fixed to a support column. Connections are located in the frame plate or, if either or both fluids make more than a single pass within the unit, in the frame and pressure plates.
Channels are formed between the plates and the corner ports are arranged so that the two media flow through alternate channels. The heat is transferred through the plate between the channels, and complete counter-current flow is created for highest possible efficiency. The corrugation of the plates provides the passage between the plates, supports each plate against the adjacent one and enhances the turbulence, resulting in efficient heat transfer.
Efficiency and Flexibility:-
· High heat transfer efficiency
· Easy to repair and cleaning
· Low fouling factor
· Compact structure, lightweight
· Easy to adjust heat transfer surface or plate arrangement
· Small temp. differential
Brazing the stainless steel plates together eliminates the need for sealing gaskets and thick frame plates. As well as holding the plates together at the contact points, the brazing material seals the package. Brazed heat exchangers are brazed at all contact points, ensuring optimal heat transfer efficiency and pressure resistance. The plates are designed to achieve longest possible lifetimes. Since virtually all material is used for heat transfer, the Brazed Plate Heat Exchanger is very compact in size and has a low weight and a low hold-up volume. We offers a flexible design that can be customized to meet customer-specific requirements. The brazed plate heat exchangers ensure the customer the most cost-efficient solution for his heat transfer duties.
The Brazed Plate Heat Exchanger consists of thin corrugated stainless steel plates which are vacuum brazed together using copper as the brazing material. Copper brazed units can be used for numerous of applications. However, for food applications and applications involving aggressive fluids, copper brazed units are not suitable.
The basic flow principle in a brazed heat exchanger for HVAC applications is parallel and current flow to achieve the most efficient heat transfer process. In a single pass design all connections are located on one side of the heat exchanger, making installation very easy.
Evaporator flow principle:-
The channels formed between the corrugated plates and corners are arranged so that the two media flow through alternate channels, always in opposite directions (counter current flow). The two phase refrigerant (vapor + liquid) enters the bottom left of the exchanger with a vapor quality depending on the operating condition of the plant. Evaporation of the liquid phase takes place inside the channels and some degrees of superheat are always requested, which is the reason why the process is called "dry expansion". In the enclosed evaporator picture the dark and light blue arrows show the location of the refrigerant connections. The water (brine) to be cooled flows counter current in the opposite channel; the dark and light red arrows show the location of the water (brine) connections.
Plate condensers – flow principle:-
The main components are the same as for the evaporator. The refrigerant enters at top left of the exchanger as hot gas and starts to condense on the surface of the channels until fully condensed, and is then slightly subcooled. The process is called "free condensation". In the enclosed condenser picture the light and dark blue arrows show the location of the brine connections. The refrigerant flows counter current in the opposite channel and is cooled. The light and dark red arrows indicate the locations of the refrigerant connections.
The real dual circuit be patented in a solution with diagonal flow is obtained by means of pressed plates. The Brazed Plate Heat Exchanger can be connected with two independent refrigerant circuits. The special design ensures that each refrigerant circuit is in contact with the entire water flow. The main advantage is that at partial load (only one compressor running) water cooling is uniform and performance is maximized.
The design options of the brazed heat exchanger are extensive. The heat exchanger can be designed as a multipass unit, different types of connections are available, and there is the option of choosing the location of the connections. We offers a wide range of standard heat exchanger models and sizes, tailor-made for HVAC applications and available from stock. Naturally, customer-specific designs are available on request.